What happens if you feed a optical node with a too high level of light

Is your training a certification course or certificate of completion? If it is certification, who is it through? If it is not, is your training recognized through any of the major associations as a step toward certification? P.S., I have heard your training is excellent. I am just inquiring as to how far it will get me.

What is the use of IOR (Index of Refraction).

Can you tell me the difference or true meanining of a composite cable and a hybrid cable. I've heard both terms used interchangeably. Are thay the same? If so then how would you differenciate between a single-mode/multimode cable vs. fiber cable/copper cable? thanks

Can you tell me the difference or true meanining of a composite cable and a hybrid cable. I've heard both terms used interchangeably. Are thay the same? If so then how would you differentiate between a single-mode/multimode cable vs. fiber cable/copper cable?

I am sending video on a singlemode fiber from building A to building B. I would like to see if i can send two cameras back from building B to building A on the same singlemode fiber. If so what equipment will I need?

Need to pad down single mode fiber between a FoxCom fiber transmitter and receiver for Satellite distribution solution. Can you recommend and solution?

Need to pad down single mode fiber between a FoxCom fiber transmitter and receiver for Satellite distribution solution. Can you recommend and solution?

When testing a fiber using and OTDR, how can the technician determine the correct IOR for the fiber in order to set the proper parameters on the test set to ensure the measurements will be accurate?

I have a number of people in my company who need training, who should I speak with?

We have to test a 9 micron loose tube outdoor fiber and a 50 micron loose tube outdoor fiber on the spool before installation. We have an FIS mini OTDR. Is there a bare fiber adapter? How would you suggest the testing be done?

I inherited a FIS 24 Port Heat Oven with thermometer and quite a few hot melt 3M connectors, but no instructions. From a 3M download, I noticed the 3M oven unit has a load adapter that one uses to insert and remove the connector from the oven port. Is the FIS oven similar? Could you give me some basic info on how the oven is used?

What should be the minimum length for an OTDR launch cable? Also, how does connecting a launch cable between the OTDR and the fiber being tested overcome the problem caused by connecting the fiber directly to the OTDRs output connector? Doesn't the "dead zone" created where the fiber is connected to the end of the launch cable casue the same problem?

Can 125um fiber be used in a 126um ferrule? Why such a close difference in size?

I inherited a FIS 24 Port Heat Oven with thermometer and quite a few hot melt 3M connectors, but no instructions. From a 3M download, I noticed the 3M oven unit has a load adapter that one uses to insert and remove the connector from the oven port. Is the FIS oven similar? Could you give me some basic info on how the oven is used?

Are there CECs offered with your fiber optic training classes?

What happens if you feed a optical node with a too high level of light?

When testing a fiber using and OTDR, how can the technician determine the correct IOR for the fiber in order to set the proper parameters on the test set to ensure the measurements will be accurate?

Is there a difference between a single mode connector (ST, SC etc) and a multimode connector?

I am using an FIS power meter and light source to test short runs of singlemode fiber , 160' and 260' on most of the strands I am getting a higer DB loss on 1550 then 1310 for example .33 / .94 or .23 / .76 Is the light source over powering the short fiber runs?

We have to test a 9 micron loose tube outdoor fiber and a 50 micron loose tube outdoor fiber on the spool before installation. We have an FIS mini OTDR. Is there a bare fiber adapter? How would you suggest the testing be done?

What should be the minimum length for an OTDR launch cable? Also, how does connecting a launch cable between the OTDR and the fiber being tested overcome the problem caused by connecting the fiber directly to the OTDRs output connector? Doesn't the "dead zone" created where the fiber is connected to the end of the launch cable cause the same problem?

I am sending video on a singlemode fiber from building A to building B. I would like to see if i can send two cameras back from building B to building A on the same singlemode fiber. If so what equipment will I need?

What is the minimum order?

When testing a fiber using and OTDR, how can the technician determine the correct IOR for the fiber in order to set the proper parameters on the test set to ensure the measurements will be accurate?

I inherited a FIS 24 Port Heat Oven with thermometer and quite a few hot melt 3M connectors, but no instructions. From a 3M download, I noticed the 3M oven unit has a load adapter that one uses to insert and remove the connector from the oven port. Is the FIS oven similar? Could you give me some basic info on how the oven is used?

If I order online, when will you receive my order?

Can 125um fiber be used in a 126um ferrule? Why such a close difference in size?

What is the index of refraction for your optical match gel: F1-0001V ?

I am using an FIS power meter and light source to test short runs of singlemode fiber , 160' and 260' on most of the strands I am getting a higer DB loss on 1550 then 1310 for example .33 / .94 or .23 / .76 Is the light source over powering the short fiber runs?

Question: Is there a difference between a single mode connector (ST, SC etc) and a multimode connector?

Can you tell me the difference or true meanining of a composite cable and a hybrid cable. I've heard both terms used interchangeably. Are thay the same? If so then how would you differentiate between a single-mode/multimode cable vs. fiber cable/copper cable?

If I order online, when will you receive my order?

We have to test a 9 micron loose tube outdoor fiber and a 50 micron loose tube outdoor fiber on the spool before installation. We have an FIS mini OTDR. Is there a bare fiber adapter. How would you suggest the testing be done.

What happens if you feed a optical node with a too high level of light?

I'm hunting for a remote fiber distance measurement. Some of our fiber runs are hundreds of kilometers from tech support. I was looking for a unit to constantly measure cable distance (ex. 80km) and if it suddenly changes to 45km, we know where the break is, and can directly dispatch the splicer... Any ideas?

What happens if you feed a optical node with a too high level of light?

What wavelengths does the FIS mini OTDR test at?

Are there CECs offered with your fiber optic training classes?

Need to pad down single mode fiber between a FoxCom fiber transmitter and receiver for Satellite distribution solution. Can you recommend and solution? Thanks,

Is your training a certification course or certificate of completion? If it is certification, who is it through? If it is not, is your training recognized through any of the major associations as a step toward certification? P.S., I have heard your training is excellent. I am just inquiring as to how far it will get me.